Feb 17 2026

Tools to help you build your Pinewood Derby Car . It's as easy as ABC!

Tip #3

It is important that your Pinewood Derby car run straight. Our Rail Rider tool is one of the easiest ways to adjust your axles for a straight running car.

Tip #8

The gap between the wheel and car body should be between 0.02" and 0.06". Our Feeler Gage, Axle Installer and Wheel Alignment tools can be used to set this gap.

Tip #42

Cutting your Pinewood Derby car can take a long time (and be very frustrating) if you don't have the right tools. For making the big cuts, try to find a friend with a band saw. A coping saw should be your next best choice.

Tip #53

After you cut your car with a saw, use a Wood Rasp to smooth the cut and give your car more shape. Use a metal file to smooth out the grooves created by the rasp.

Pinewood Derby Car Tools

The parts that are included with your Pinewood Derby car kit are far from perfect. The tools on this page will fine tune your wheels and axles for maximum performance and build a fast Pinewood Derby car.

Pro Hub Tool

For use with the Pro Wheel Shaver and Pro Hub Shaver

The Pro Hub Tool is used with the Pro Wheel Shaver and Pro Hub Shaver. These tools include the Pro Hub Tool but you can order a replacement Hub Tool here.

OUT OF STOCK

Pro Wheel Shaver XT 2

Eliminate Wheel Imperfections

The Pro Wheel Shaver is one of the easiest, most efficient and cost effective ways to create perfectly round wheels from a molded standard wheel. Not all wheels are created equally, but with a Pro Wheel Shaver, they can be made Hi-Performance. The Pro Wheel Shaver can minimize speed loss caused by the following wheel defects:

Out of round wheels cause improper alignment causing your Pinewood Derby car to pull to one side or oscillate. With this tool, you can shave the high spots off until your wheels are completely round.
The inside edge of a most wheels is not straight. The most perfect aligned cars will still touch the center strip a few times on the way down the track. The inside edge of the wheel will determine what happens when contact is made. If the inner edge is not true, it will cause the car to sharply turn in the other direction slowing the car down.

Watch Blade Sharpening Video

How to Use the Pro Wheel Shaver

Pro-Wheel Shaver and Hub Tool

OUT OF STOCK

Pro-Wheel Shaver

(Pro-Hub Tool Required)

OUT OF STOCK

Replacement Blade

For Pro Wheel Shaver OUT OF STOCK

Pro Hub Shaver

Reduce friction between axle head and wheel

The Pro Hub Shaver is designed to condition the outer wheel hub face that rides under the axle head and remove any defects and burrs. It can also remove the extra step in the new B.S.A. wheel helping to create a faster wheel.

How to Use the Pro Hub Shaver

The Pro Hub Shaver can be ordered with or without the Hub Tool but the Hub Tool is required.

OUT OF STOCK

Pro Rail Rider Tool

Axle Alignment the easy way

The Pro Rail Rider is used with the Pro Axle Press to align your car to run straight or to tune it to use the new "Rail Riding" technique for even faster speed. Full instructions included.

How to Use the Pro Rail Rider

OUT OF STOCK

Pro Body Tool

Make Perfect Axle Holes

The Pro Body Tool is a drilling aid to help create correctly placed axle holes on the body or correct mis-aligned slots in stock blocks when rules require their use.

Easily place the axle holes perpendicular to the centerline of the car so your car will go straight down the track.
Locate all of the axle holes at the same height on the body so the car sits square on the track.
Reduce friction!!! By correctly placing the axles in the body, a builder will not have to bend or tweak the axles to get the car to run straight.
Can drill holes for raised wheels.

A hand drill is required. This tool is equipped with guide hole for BSA, PineCar, and other kits requiring a #44 drill bit. A #44 drill bit is included.

How to Use the Pro Body Tool

OUT OF STOCK

Pro Bore Polisher

Your wheels can be made to spin even better than ever.

The Pro-Bore Polisher will improve the speed of your car by reducing friction between the wheel and axle inside the wheel bore.

Eliminates plastic debris and minimizes flaws inside the wheel bore
Polishes the wheel bore to a high shine.

Includes drill attachment, two pipe cleaners and micron plastic polish.

A hand drill is needed to use this tool.

How to Use the Pro Bore Polisher

OUT OF STOCK

Pro Bore Wax

Wax your wheels for more speed

Waxing the wheel bore will reduce friction between the wheel and axle. This is a speed trick that is usually overlooked and, when used with our Pro Bore Polisher, can give your pinewood derby car a significant speed advantage.

Works well with graphite and liquid lubricants.

How to Use the Pro Bore Wax

OUT OF STOCK

Axle Guide

Another tool to install your axles

The Pro Axle Guide is a precision machined aluminum block with a laser cut tab designed to fit in the axle slot of most pinewood derby car bodies. The tab is designed to give the wheels the proper spacing from the body. The block can also be used on the flat side for extended wheel base cars.

How to Use the Pro Axle Guide

OUT OF STOCK

Axle Pliers

Handy tool for removing axle and adjusting alignment

For removing axles from pinewood derby and awana cars. This is also the only tool that can turn a bent axle to adjust the alignment of the car without damaging the axle.

OUT OF STOCK

Feeler Gauge

Sets the correct gap between car and wheel

This stainless steel feeler gauge is ideal for setting correct distance between the wheel hub and car.

OUT OF STOCK

1 1/8" Forstner Bit

For drilling holes for our
Tungsten Disc or for removing wood from the car body.
Fits any 3/8" or larger drill

OUT OF STOCK

1" Forstner Bit

For drilling holes for our
Tungsten Domed Slotted Disc or for removing wood from the car body.
Fits any 3/8" or larger drill

OUT OF STOCK

#44 (.086" diameter)

Axle Drill Bit

This drill bit has a slightly smaller diameter than the official BSA axle and is perfect for drilling new axle holes or for aligning the existing axle slots.

OUT OF STOCK

Wood Rasps

Make building your car easier

Rasps are used to shape your Pinewood Derby car block after it has been cut with a saw. Rasps are also great for rounding sharp corners and cutting groves into the wood. Rasps have rough teeth that can quickly remove a lot of wood. After you use a rasp, a file or sandpaper can be used to smooth the block. More about rasps

Wood Rasp

Sold as a set of two rasps, one is flat and the other is half round.
OUT OF STOCK

Axle Files

Axle files are used to remove the burr and crimp marks on axles.

This file should be used on an axle that is mounted on a drill and spinning.
Use fine grit sandpaper to polish the axle after it has been filed.

Car Building Supplies

Body Putty

Includes spatula

Ideal for:

Filling scratches, cuts, gaps and rasp marks.
Adding fins, spoilers, bumps and other features to your car.
An all-over smooth finish.

OUT OF STOCK

Super Glue

Bonds to almost anything. Sets in seconds.

Ideal for attaching accessories, parts and weights to your car.

OUT OF STOCK

Sandpaper

Three 4" X 5" sheets

Ideal for sanding your
Pinewood Derby car.

OUT OF STOCK

Glue

Dries clear

Ideal for:

Attaching axles to your car.
Repairing chips and cracks on your car.

OUT OF STOCK

Customer Photos

Brad Barnett used our Jet pre-cut car blocks to create a Blue Angles F-18, SR-71 Blackbird and Thunderbirds F-16. The RSX wheels on the Blackbird make it extra fast.

Shane Hart and his Dad used many of our tools to build his car. He won 1st in the Den and 2nd in the Pack!

George Myers used our Pro tools to help build his Pinewood Derby car. He won first place in 23 heats.

Pinewood Derby Build

Build a Car

Make it Fast

Make it Look Great

Extras

Male

Information

How To

We used your hub tool, wheel mandrel and bore polisher when making our pinewood derby car. My son raced in 23 heats and won all 23 of them. His car was the fastest and best looking of the district. Thanks for your Help,....Kurt M

Thanks for the quick delivery. Your tools really made it much easier to get our cars ready. Jim R.

I placed my order online, received your products in just a few days and then scoured your website for tips on how Joshua and I could build a fast car. You've got it down! Thanks again,
Rob and Joshua

I wanted to email and Thank You for your help and answering all my questions. My son's car won first place in his Den and first place overall in his Pack. He then went on to race in the Council wide race. He won first place in his den level and again first place overall. Just wanted to let you know. Thanks again, Mike

Thank you for the shipment. My son won the fastest pinewood derby car in our hole pack!!! He is delighted.
Thanks... Sykes M

We almost won. We got beat by the family that has won for the last 5 years in a row. They had an average speed of 161.1 and we had 161.0. Thanks for all the great products....Steve C

Thanks again for sending out the stuff so soon. The axle puller works great!! I think there will be more people looking for your wheels after my car beat most of them. Came in second, beat by 0.023 seconds ... I won Best Overall Design though for the open division. Scouts had their own. I used that puller several times for the shuttle of my sons, I kept pushing them in crooked, had to keep trying and it made it so much easier. He also won second, missed it by mere millimeters, beat by the last foot or two, so close...Kevin R

Thank you, My son won first place in speed in our pinewood derby race for the third year in a row. His speed was 2.79 seconds all three years. There was only 1 other car in the race who posted a 2.79 in their first race, but then their times got slower as the races went on. I do believe that the bore polish and axle polish were helpful on the stock wheels, and speed axles I used this year. Thank you, Dean B

Thank you for the axle installer. It worked perfectly and is very ingenious... Roger C

Received my order - everything arrived fine - and nicely packaged by the way! As a retired mechanical engineer, I wanted to compliment you on the workmanship that went into these tools - nice work! Clearly you put a good amount of effort into the little stuff that makes good tooling. Regards, Kelly B

I got the axle bender, it worked great. We got 2 place in den and 3rd in the Pack! Thanks for a great tool!.... Sparky G.

We did the race on Feb 20th. Now I am not handy at all. When I was a child I entered the derby one time. In the first heat the car hit the bottom of the ramp and the wheel came off. That was it. I was done. It was fairly traumatic for a 10 year old boy. Now my son is 7 and I wanted to make sure that didn't happen to him. Outside of the cutting he did all the work with me going back to clean it up or fine tune it. We lasted through the 3rd round. In 6 heats we won twice, finished second twice and third twice. I know our problem was one of the front wheels was sticking depending on if it was against the car or the axle head. We'll do better next year. It was an absolutely GREAT, TERRIFIC father-son experience. We had so much fun.....
Andy B.

The axle bender arrived just in time. My son had the fastest car out of his den, but also the entire pack! This was our first time competing and we left a lot of people scratching their heads! Thank you so much for your efforts. Had I not gotten that axle bender, I know our times would not have been as good. Can't say how much I appreciate it. .... Steve C

Just wanted to say a big thank you for your help!! You saved the day with our pinewood derby science fair project. We will be back on your site later this year when we start prepping for the Cub Scout derby car :) Thanks again!...Jess